You are not logged in or registered. Please login or register to use the full functionality of this board...

Latest news: --- EPC/WIS/ASRA 08.2017 TORRENT --- SDT-11 Suzuki --- EPC/WIS/ASRA 08.2017 TORRENT --- Password --- Free download SKP1000 key programming V8.19 sofware --- vw fox sistema i motion --- Toyota Industrial Equipment EPC v2.02 [07.2017] Full Instruction + Serial --- Free Download 2017 ETKA 8 and how to install ETKA 8 v2017 --- LEXUS IS220d Dpf Emulator wiring diagram --- Help me ---

Automotive Diagnostic Tool

Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Op-com firmware 1.64
08-21-2016, 08:33 AM (This post was last modified: 05-06-2017 01:08 PM by kingarthas.)
Post: #1
Op-com firmware 1.64
Do not forget, I can not take responsibility — all manipulations with the device you are doing at your own risk!
When a "brick" one request in this is not to blame!

For a new program VAUX-COM is not necessary to update to 1.64; The
program will quietly work on version 1.45 (Download VAUX-COM program,
you can ). Sews mostly owners of new cars need to access new blocks.

Before starting work, dismantle its OP-COM and see the presence of PIC18F458 chip.
Sews only the Soup in which a chip PIC18F458 controller, and those who have written on the chip OP-COM — you can stop reading.


[Image: 30b6562s-960.jpg]
See here the presence of the chip. There must be a PIC18F458. If you have a OP-COM chip then do nothing. Get a 100% dead OP-COM

[Image: b4d0adcs-960.jpg]
Here is an example. Instead PIC18F458 chip is OP-COM chip. It can not reflash. Get a 100% dead OP-COMAfter we have seen that in our OP-COM is the chip PIC18F458 go to the next step.


Connect OP-COM to the computer.
Set VAUX-COM_120309a + 131223d_GB + OcFlash China
In order to verify the correct installation of the drivers necessary to run the program VAUXCOM.exe
Hit Settings
Hit Test interface.


[Image: a0fe1bas-960.jpg]
Should such a label will appear here. This means that the driver will be installed properly

[Image: c8a61bas-960.jpg]
If
there was such a sign, the driver has not been established and will
have to install them manually. To do this, go to the link below
If the driver's OK then close VAUX-COM.
Download the firmware
run the program OCFlash.exe


[Image: d7d6562s-960.jpg]
OCFlash.exe

[Image: 35011bas-960.jpg]
Specify the path to the downloaded firmware 1.64
Run the Test interface again and check that the OP-COM updated to version 1.64
You can now use the program VAUXCOM.exe


[Image: 9d0e562s-960.jpg]
Machinery until 2014. Smile

[Image: 8611bas-960.jpg]


Downloaded:
1192 times Headbang

Thanks given by: autodaso45 , VirgilLiviu78 , joeblack15 , Baron , mdanilo , clico70 , opel17 , zeltini1401


Attached File(s) Thumbnail(s)
   

kingarthas, proud to be a member of GarageForum since Nov 2015.
Visit this user's website Find all posts by this user
Quote this message in a reply
 Thanks given by: autodaso45 , VirgilLiviu78 , joeblack15 , Baron , mdanilo , clico70 , opel17 , zeltini1401 , DarkAdi , WannaCry , suppersready , turismo005 , Jupsu3 , jaroza , cougar66 , VLStelios , microcris , 5845olaf , marcel1988 , Eisy , Dydycom
08-27-2016, 04:24 PM
Post: #2
RE: Op-com firmware 1.64
great. thank you.

VirgilLiviu78, proud to be a member of GarageForum since Jun 2016.
Visit this user's website Find all posts by this user
Quote this message in a reply
 Thanks given by: zeltini1401
08-31-2016, 06:58 PM
Post: #3
RE: Op-com firmware 1.64
hallo, were we can get the 131223c EN with latest official ver data folder paste over?

joeblack15, proud to be a member of GarageForum since Aug 2016.
Visit this user's website Find all posts by this user
Quote this message in a reply
05-08-2017, 11:34 AM
Post: #4
RE: Op-com firmware 1.64
Where can i download the firmware?

DarkAdi, proud to be a member of GarageForum since Dec 2016.
Visit this user's website Find all posts by this user
Quote this message in a reply
06-12-2017, 05:13 AM
Post: #5
RE: Op-com firmware 1.64
good illustration

say882, proud to be a member of GarageForum since Jun 2017.
Visit this user's website Find all posts by this user
Quote this message in a reply
06-18-2017, 04:46 PM
Post: #6
RE: Op-com firmware 1.64
(08-21-2016 08:33 AM)kingarthas Wrote:  Where can I download the software?
(08-21-2016 08:33 AM)kingarthas Wrote:   Do not forget, I can not take responsibility — all manipulations with the device you are doing at your own risk!
When a "brick" one request in this is not to blame!

For a new program VAUX-COM is not necessary to update to 1.64; The
program will quietly work on version 1.45 (Download VAUX-COM program,
you can ). Sews mostly owners of new cars need to access new blocks.

Before starting work, dismantle its OP-COM and see the presence of PIC18F458 chip.
Sews only the Soup in which a chip PIC18F458 controller, and those who have written on the chip OP-COM — you can stop reading.


[Image: 30b6562s-960.jpg]
See here the presence of the chip. There must be a PIC18F458. If you have a OP-COM chip then do nothing. Get a 100% dead OP-COM

[Image: b4d0adcs-960.jpg]
Here is an example. Instead PIC18F458 chip is OP-COM chip. It can not reflash. Get a 100% dead OP-COMAfter we have seen that in our OP-COM is the chip PIC18F458 go to the next step.


Connect OP-COM to the computer.
Set VAUX-COM_120309a + 131223d_GB + OcFlash China
In order to verify the correct installation of the drivers necessary to run the program VAUXCOM.exe
Hit Settings
Hit Test interface.


[Image: a0fe1bas-960.jpg]
Should such a label will appear here. This means that the driver will be installed properly

[Image: c8a61bas-960.jpg]
If
there was such a sign, the driver has not been established and will
have to install them manually. To do this, go to the link below
If the driver's OK then close VAUX-COM.
Download the firmware
run the program OCFlash.exe


[Image: d7d6562s-960.jpg]
OCFlash.exe

[Image: 35011bas-960.jpg]
Specify the path to the downloaded firmware 1.64
Run the Test interface again and check that the OP-COM updated to version 1.64
You can now use the program VAUXCOM.exe


[Image: 9d0e562s-960.jpg]
Machinery until 2014. Smile

[Image: 8611bas-960.jpg]


Downloaded:
1192 times Headbang

Thanks given by: autodaso45 , VirgilLiviu78 , joeblack15 , Baron , mdanilo , clico70 , opel17 , zeltini1401

eucosta, proud to be a member of GarageForum since Jun 2017.
Visit this user's website Find all posts by this user
Quote this message in a reply
 Thanks given by: marcel1988
07-13-2017, 04:22 PM
Post: #7
RE: Op-com firmware 1.64
hi where can i download it

marcel1988, proud to be a member of GarageForum since Jul 2017.
Visit this user's website Find all posts by this user
Quote this message in a reply
08-16-2017, 01:23 AM
Post: #8
RE: Op-com firmware 1.64
Hi , where can I get the link to download

Zaidoun, proud to be a member of GarageForum since Aug 2017.
Visit this user's website Find all posts by this user
Quote this message in a reply
08-23-2017, 07:05 AM
Post: #9
RE: Op-com firmware 1.64
(08-16-2017 01:23 AM)Zaidoun Wrote:  Hi , where can I get the link to download
I think you need to buy premium.

Dydycom, proud to be a member of GarageForum since Aug 2016.
Visit this user's website Find all posts by this user
Quote this message in a reply
Post Reply 


Forum Jump:


User(s) browsing this thread: 1 Guest(s)